7.25.2011

Working!

Recently started doing some building for a certain boutique pedal company (that will not be named yet). I'm really happy to be doing it, and hope it lasts! I've been a fan of this company for a couple years now so this is cool as hell, haha.

7.17.2011

ILFuzzFace

Last year, I built my first and only fuzz face. Got a loaded FF board, all NOS, from Forrest at circuitworkshop/capsnsuch.com. I played with a few ideas for the finish, until I got something I really liked.


I started with a few extra ILoveFuzz stickers. Two, actually. Some placement, fine trimming, and we're left with a face/skull. A Fuzz Face circuit in an enclosure with a face made from the words "ILoveFuzz." Yeap.

After the stickers were in place, I used a two part epoxy over the top. Inspiration for this came from Sonic Crayon and McSpunckle. I then sanded the sides down flush. Would have been much easier with a belt sander.


If you're going to give the epoxy top a try, I'll offer two tips: Drill before laying the epoxy down. You may notice some discoloration where the knobs and 3pdt switch are. This is from the resin pulling away from the enclosure. Also, as you can see lots of bubbles formed in the finish. A better quality epoxy may help with this, as well as proper mixing. McSpunckle said using a torch will remove the air bubbles as well.


The small pot on the side is the bias. Goes from smooth to splatty, and sounded great. I'll have to see if its current owner will record a clip for me. I got this thing finished on Halloween, so the theme was more perfect. Ironically enough, I sent this out as a Christmas present for Ryan from Dr. Scientist, in last years ILF Secret Santa.

I wish I had gone back and trimmed the wires down a bit and cleaned it up, but it's not too bad.

Space Saver

Haven't got anything new ready to post yet, so here's some more projects from back then.


Cinos Titan, aka another Sonic Titan workalike.


The Sleasy Drive, a workalike of Joe Davisson's Easy Drive



Footswitch for my Sears 40xl




6.28.2011

Brass-fromthepast-Master

My first brassmaster build. So sad that I didn't get enough for two of these cause let me tell you, I did NOT want to send it off when she was all finished up. Sounds fantastic, with tons of tonez on tap. Maybe I can get Nate (the recipient of this gem), to toss up a clip eventually. My computer was AWOL for a few weeks so I couldn't make clips...at least we can look at it, right?

The finish was something I tried to to keep close to the original. My initial design was actually almost just like the orig, but I changed my mind last minute. I actually used hammerite type paint for the triangle, for some depth or added effect.

Here's the Spritzer, getting acquainted with some of my other pedals. The name "Spritzer" comes from a Maestro ad from back in the day. Talks about a musician named Harvey Spritzer, who's lost work due to the introduction of the Brassmaster.

What the insides look like. As you can see, this was quite the squeeze. Now if only I had made a drill template the first time so I don't have to measure all that out again for the next ones. Ideally, the power leads (black and red wire right up the middle) would have been under the board, but there just wasn't enough space. The LED is directly under the dc jack, up against the pcb.

Thanks to General Guitar Gadgets, for supplying the goods for me to build this. They have complete Kits available, with options for enclosures, predrilled, etc. You could also buy just the PCB if you have the parts around, or are trying to save money. I recommend the full kit, as it will save you tons of time and hassle sourcing individual parts. If this is your first build, I might try something simpler as all those connections can become overwhelming rather quickly.



5.20.2011

Upcoming

I'm working on a few builds right now, so I will have new stuff up soon!

5.04.2011

My recent day off

Finally got a day off after a couple weeks, so it was time to build something! 

A long time friend, Paul, painted an enclosure for me many months ago. I had it sitting around forever waiting for the right circuit to match it with. Decided on the AMZ Jfet Splitter, by Jack Orman. Takes your input signal and splits it into 2 (or more) equal outputs.


Something like this can be very useful with some planning. For instance, I've been using it to run modulation to the effect channel (trem & verb) on my silvertone, while the other out runs dirt to my "clean" channel. Makes it easy to set things in the mix. With both channels running together, you can EQ them slightly different, which makes for some great, full tone. Of course you could also make any effect stereo...think of the possibilities with things like delays that are already stereo...



 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

This here is an Electra type circuit designed by Renegadrian. Gives more gain to the original. The Lovepedal Woodrow can be built with the same layout. I have everything socketed (good thing too), so I'm still tweaking to my liking. As it was, way too loud and trebly. The toggle switch will be for swapping clipping diodes most likely, or maybe cap values for treb/bass.




The enclosure is from a walco boost type pedal, that I actually had a diff boost built into for a while. There was an extra hole on the bottom front from the orig layout, so I decided to make this a "window" for the LED. I glued in some foggy vinyl material to diffuse it and seal the opening.












Filler


While I'm in between projects I figure I could fill some space with more earlier builds, that were forgotten about. Just random stuff from the past year or two.

Here's a modified Crybaby Wah (JH-1).

Don't remember exactly all that I did...obviously painted the top. Removed it entirely, along with the rubber grip prior to. Changed the tone voicing slightly for a better match with bass. The jh1 is set stock in between the normal crybaby and bass version. There's a wah voice control now, that really makes the pedal much more musical. The toggle switch removes a cap to change from wah to volume. Pretty neat, but not the greatest sweep for a volume pedal.
I believe some/most of the mods can be found at Stinkfoot's page.

                        ++++++++++++++++++++++++++++++++++++++++++++++++++

Next up, a custom job for CBA713 of ILoveFuzz that I apparently did in August. It's a voltage starve, a la Beavis Audio's Devolt, that C' dubbed, "Jervolt."


                             +++++++++++++++++++++++++++++++++++++++++++++++

Some of you may recognize this one. It's a Melx2 from Mellowtone. Similar to the Electra Distortion of yesteryear, it's a great dirt box that I will always have. Mine is only slightly different from the ones you'd normally see. I added a switch to change between clipping diode pairs...1n914?(stock, silicon) & some germanium ones I got out of an old busted walco pedal.